AEM V3 One Gallon Water/Methanol Injection Kit – Multi Input – 30-3350

Description

• About Product
• Additional Details
• About the Brand

AEM V3 One Gallon Water/Methanol Injection Kit – Multi Input

Water/methanol injection for forced induction (turbocharged or supercharged) gas-powered race engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation. This allows racers to reliably increase boost and advance ignition timing-without using high-octane racing fuel-for power gains of up to 20%. AEM’s Water Injection Kits utilize robust hardware and deliver more advanced features than any other comparably priced water/methanol injection system.

V2 Water/Methanol Injection Kit, Multi Input Controller – 0-5v/MAF Frequency or Voltage/Duty Cycle/Ext MAP, 200psi WM Pump, 1.15 Gallon Reservoir, Conductive Fluid Level Sensor

Boost Dependent and Multi-Input (0-5v/frequency) progressive controller designs feature large adjustment knobs, integrated plug for harness connection, integrated fuse, covered status light and test button for enhanced splash resistance and mounting tabs Wiring harness is terminated with a positive-lock connector on one end with color-coded wires to ease installation, integrated pump ground circuit and additional wire for optional on/off fluid solenoid “Boost Safe” failsafe output included (for complete failsafe under all conditions, see our Water/Methanol Failsafe Device) Heavy-duty high-pressure injection pump features integral fittings, a Santoprene diaphragm and EPDM seals to resist corrosion. Our pump maximizes line pressure for optimum atomization and its quiet, smooth operation is almost undetectable Precision-machined billet-aluminum injector with integral check valve Three interchangeable injector nozzles to cover a wide variety of HP levels (250cc/min, 500 cc/min & 1,000cc/min) 1.15-gallon tank with anti-starvation reservoir, integral conductive low-fluid sensor and positive lock connector (tank-less systems available) 20 feet of injection tubing included LED dash light for system status and low fluid warning. Combined with the integral and highly accurate conductive low-fluid switch in the tank, “Boost Safe” can also put your engine in safe mode before the system runs dry. This exclusive feature is found only on AEM Water/Methanol Injection Systems. Revised Flow Control Strategy for More Linear Fluid Delivery AEM’s engineers spent extensive time revamping the controller’s flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine’s need for water/methanol injection, which further optimizes charge air cooling and detonation control.. Integrated Boost Safe Feature The controllers in AEM’s Water Methanol systems include an integrated “Boost Safe” output feature that monitors the entire injection system and triggers a ground signal via an output if it detects a voltage-related error (short, bad connection, broken wire, overheated pump, high or low voltage signal, etc.), allowing users to define their failsafe strategy from something as simple as flashing a warning light to more advanced strategies like pulling boost or ignition or switching fuel maps on a standalone engine management system.. Simplified Wiring AEM’s Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.. Low-Profile 1.15 Gallon Tank AEM’s gas Water/Methanol Injection Systems are available with or without a compact 1.15 gallon tank that features an anti-starvation reservoir. A more accurate, conductive low level fluid sensor is integrated into the tank and features a positive lock connector with color-matched wires to the wiring harness.. Heavy-Duty Waterproof High Pressure Injection Pump – Safe for Engine Bay/Frame Rail Mounting AEM’s internally-bypassed water/methanol injection pump is waterproof and safe for mounting in loactions that are exposed the elements.. It does not cycle on and off and provides quiet, smooth operation. It features robust construction including integral hose fittings, EPDM seals and a Santoprene diaphragm that provides consistent and reliable fluid delivery.. Terminated harness features positive lock connector with integrated pump ground circuit and additional wire for optional on/off flow solenoid. The sensor eliminates any chance of incorrect readings due to interference from debris.. One machined billet injector with integral check valve to prevent unintended flow. Recirculation-style pump with integral fittings for quiet operation. AEM V3 One Gallon Water/Methanol Injection Kit – Multi Input. AEM V3 Naturally Aspirated Water/Methanol Injection Kit. LED dash light for system status and low fluid warning. Includes “Boost Safe” readiness failsafe system. 20 ft. of high-pressure Nylon injection tubing. H2O INJ KIT V3, EXT MAP, 1GAL. AEM – Water/Meth Injection. Water Injection System Kit. Water/Meth Injection

Forced induction components mainly consist of supercharger or turbocharger parts that are used to make significant power gains on your vehicle. If you are looking for a significant increase in horsepower, look no further than forced induction.

Additional Details

NOT CARB-APPROVED. ILLEGAL TO USE OR INSTALL IN CALIFORNIA. IF YOU LIVE IN CA, WE CANNOT SHIP YOU THIS ITEM AND YOU WILL BE CHARGED A 10% CANCELLATION FEE IF YOU ORDER. PLEASE LOOK FOR OTHER PRODUCTS WITH CARB APPROVAL.

WARNING: Cancer & Reproductive Harm. For more information, go to www.P65Warnings.ca.gov

Installation Instructions

1. Click to Download

About AEM

AEM was founded in 1987 by John Concialdi (J.C.) and Bob Sullivan as a tuning performance shop. The shop focused on vintage automobiles and the latest trends in street racing modified imports. With it’s location in Compton California, AEM was embedded in the tuner market from the very beginning. It was a matter of being in the right place, at the right time, with the right technical knowhow. Between J.C. and Sullivan, AEM had two important advantages. Technical engine knowledge and massive creativity fueled by an unbridled passion to make things go faster. When it came to understanding air flow through an engine, few had more experience than Concialdi. He managed the R&D department for Weber Carburetors for North American aftermarket applications the previous 10 years. By 1993 when the shop relocated to Gardena California, AEM had the reputation as a modifier of choice. The business had grown so much that at times it ran 24 hours a day. Racers depended on AEM to have cars ready for the next street race or sanctioned event. Cars and drivers sporting AEMs bright yellow logo became famous in the street racing scene for one consistent reason, they won races. AEMs first glimpse of mainstream notoriety came when cars tuned by their shop won at the Battle of the Imports. This highly contested shoot-out landed AEM on the cover of Turbo Magazine and Sport Compact Magazine. Many of the most visible drivers in import street racing ran cars modified by AEM. This included names like Adam Saruwatari, Tony Fuchs, Brian Kim and Darin Ishitani, Archie Medrano, Russ Matuseavich, Abel Iberra, Miles Bautista, E.T. Saffon.AEM developed one of the first Packaged Air Induction Systems. It’s design came from their experience in dyno testing, understanding intake energy dynamics and racing at the Battle of the Imports. AEMs presence in the tuner movement and its proximity to Nissan, TRD and Honda allowed them a unique opportunity. There was an advantage to living side by side with racers and working with OES engineers. AEM was able to understand both the practical and theoretical side of engine performance. AEM’s first air intake kit was offered for sale in 1994 as a “Do-It-Yourself” upgrade for the Honda CRX. This intake proved to be the beginning of a whole new tradition. People could suddenly purchase affordable cars and modify them for increased torque and horsepower. AEM has been a leader in the development of precision tuned induction systems since the Battle of the Imports. Today, the Companys induction systems number in the hundreds. AEM is still the one to beat.